turbo: recapitulatif des IHI VF**

[agron-subaru-sti-passion 0]

voila vu que le forum est nouveau
on pourrait remettre les caracteristiques de chaque turbo ici

[dadam 0]

voila une idee qu'elle est bonne! et qand tu dis REmettre ca veut dire quoi?

[agron-subaru-sti-passion 0]

dadam a écrit:

voila une idee qu'elle est bonne! et qand tu dis REmettre ca veut dire quoi?

ben c etait sur un autre forum que tu allais pas

[Hadès11 0]

The VF series (VF22, VF23, VF24, VF29, VF30, VF34, VF39) are the most common direct replacement turbos. All VF-series turbochargers use the same roller bearing, water-cooled core assembly. The differences are in their wheels and housings to achieve different flows.

The VF22 has the largest potential for peak horsepower. In other words, in the IHI model range, the VF 22 supports the highest boost levels. It is capable of running up to 25 psi. Because it is a roller bearing turbo, turbo lag is minimal...the boost comes on around 3300 rpm. Expect to max out the VF22 somewhere in the 400-450 hp range.

The VF23 starts the middle ground. It comes on boost around 3100 rpm and is capable of running 20 psi of boost. Expect to max out the VF23 somewhere in the 300-350 hp range.

The VF 24 starts to come on around 2900 rpm and will significantly improve power through the midrange over the stock TD04 turbo. However, the VF 24 is only capable of running around 17 psi.

The VF23 and VF 24 are a great replacement for those who value drivability higher than maximum power.

The VF29 & VF30 delivers a very wide increase in torque over the standard TD-series turbos.

The VF 30 is a fairly new IHI model that utilizes the exhaust housing of a VF24 and the compressor housing sized between a VF 23 and a VF 22. It comes on boost down low (around the 3000 rpm range). With upgraded injectors, fuel pump, and engine management, the VF 30 is good for 365-390 horsepower. It is important to note that the VF30 is NOT a roller bearing turbo.

The IHI VF34 (which comes standard in the Japanese market STi version "RA") is a new roller bearing turbo. It has the same specifications (compressor size, etc.) as the VF 30. The difference lies in the roller bearing which, theoretically, allows quicker spool and better response. It costs a couple hundres more than a VF 30. The VF 34 maxes out around 365-390 hp. It is probably the most popular option for big turbos on the WRX.

One other turbo to note is the VF 39...it comes standard in the USDM STi. While we don't have all the specs yet, these are a new roller bearing, TWIN SCROLL design. Performance numbers are pretty similar to the VF34...maxing out just under 400 hp.

A new high performance modified IHI turbo has made its way to the market recently. They are the Power Enterprises PE 1818 and the 1820. The 1818 supposedly comes on boost extremely fast...which make it great for road racing or aggressive driving (remember to be responsible :^). The 1818 maxes out somewhere between 350-375 hp.

The 1820 is larger than the 1818 and is capable of running more boost, but at the expense of more turbo lag. Expect it not attain full boost until you have passed 4000 rpm. However, it can be tuned to 400+ hp.

[Hadès11 0]

Pour ceux qui ne comprennent pas l'anglais :

http://www.google.fr/language_tools?hl=fr


Mais bon c'est approximatif

[sti04 0]

et le VF43 des sti 2.5 ??

[Hadès11 0]

sti04 a écrit:

et le VF43 des sti 2.5 ??

J'ai lu sur le montreal club qu'il était donné pour 330 cv max.

Pour le VF35 la plupart savent à quoi s'en tenir, très bon spool, 350 cv environ.

[agron-subaru-sti-passion 0]

sti04 a écrit:

et le VF43 des sti 2.5 ??

comme le TD04 de la WRX
ok

[sti04 0]

bref, je suis mal barré

[agron-subaru-sti-passion 0]

sti04 a écrit:

bref, je suis mal barré

non plus serieux
il disait entre 330cv a 350cv sur certain forum
gp tuning a sortit 370cv
mais en changeant le turbo

[Kosmic 0]

J'aimerais rejouter au topic. La meme information que plus haut avec quelques points en plus. Merci.

VF22:
This turbo has the highest output potential of all of the IHI VF series turbos and is the best choice for those who are looking for loads of top end power. The top end power however, does not come without a cost. The VF22 spools significantly slower than the rest of the IHI models due to the larger P20 exhaust housing and is much less suited for daily driving than some of the other models. Although the largest VF series turbo, the VF22 is not quite optimal for stroked engines or those who wish to run more than 20PSI of boost. The VF22 is best mated with the 2.0 block and in applications of 20lbs of boost or less.

VF30:
The VF30 is commonly considered the best bang for the buck turbo in the IHI VF series line. A relatively new model the VF30 features the the same exhaust housing as the VF24 but a larger compressor side similar to the VF22. The combination of these two parts results in increased output potential without the lag associated with the VF22. Although it doesn't offer the top end supremecy of the VF22, the VF30 is a great compromise between these unit and the quicker spooling models.

VF34:
The VF34 is nearly identical to the VF30, with the same exhaust housing and compressor. However the VF34 goes back to the ball bearing design, and in doing so achieves full boost approximately 500RPM sooner than the comparable VF30. The VF34 is the most recent IHI design and as such costs slightly more than its counterpart. Top end performance and maximum output are identical to the 30.

Provided by Dark Rex (*Information was derived from many sources including NASIOC, MRT website, PPMotorsports website, clubwrx.net, scoobytech.net, WorldOne and Rallispec website.)

VF23
This turbo is considered a great all-around turbo. Like the VF22 it utilizes the largest P20 exhaust housing. This housing is mated with a smaller compressor housing of the of the VF24 for fast response and excellent low and mid-range performance. It does not have the same top end power of the VF22, but spools up significantly quicker. Standard ball bearing center section. Excellent bolt-on replacement for the standard WRX turbo on cars without any other major modifications. Expect flows around 430 CFM at 18 PSI.


VF24
This turbo shares its compressor housing with the VF23 however, this housing is mated with a smaller (P18) exhaust side. The smaller characteristics of this turbo allow it to provide ample bottom end power and quick spool. This turbo is very popular for Imprezas with automatic transmissions and Group N rally cars. Not recommended for stroker engines or engines with high boost as turbo is small and can over speed. Best turbo for cars that want the best bottom end and least lag. Expect flows around 425 CFM at 18 PSI


VF28
This turbo came standard on the STi Version 5. In terms of overall size, it is smaller than the VF22, VF30 and VF34, and about same size as the VF23. Expect flows around 425 CFM at 18 PSI


VF29
This Turbo is nearly identical to the VF24, with the same compressor and exhaust housings. However the compressor wheel in the VF29 is has been changed slightly. The changes made to the compressor wheel in this model are generally viewed as improvements, and as such this unit is typically chosen over the VF24. Has a different location for the pressure hose on the waste gate actuator Expect flows around 425 CFM at 18 PSI

VF35
The VF35 utilizes the same compressor housing as the VF34 however it also features a divided thrust or offset ball bearing design. The smaller P15 exhaust housing for quicker spool up and a slightly more limited top end. The compressor inducer size is the same as a VF30/or 34 turbocharger.